[Config]
Program=nvgsms
Port=COM1
Mode=2400,N,8,1
Description=
RemoteSystemName=SMS Modul
PhysicalLayer=Modem through RS232
WatchTimeout=6
MoveJobToDoneOrErrorPath=1
WriteToJournalLog=1
JobProcessingLimit=1024
WatchPath=\nvt\nvgsms
FileMask=*.sms
DonePath=\nvt\nvgsms\done
ErrorPath=\nvt\nvgsms\error
WatchLogPath=\nvt\log
WriteIncomingSMSJobFile=0
IncomingSMSJobPath=\nvt\nvgsms\incomingSMS
* Format of execution oft the file is 'start <CmdLineFormat> .=*
* If WriteIncomingSMSJobFile is 0 it should be a batchfile with it's parameters (start incoming_sms.bat %s %s) .=*
* If WriteIncomingSMSJobFile is 1 defined it should be the module nvincomingsms.nve (nve nvincomingsms.nve -s1%s) parameter is the IncomingSMSJobFile .=*
CmdLineFormat=start incoming_sms.bat %s %s
* To deactivate the old function and use the nvincomingmessage started over jobfile with WDir, then set this value to 0 .=*
UseOldIncomingFunctions=0
* If this should work in a redundant system as confirmation, we need to make a request to NVR=*
WriteIncomingSMSJobFileToNVR=0
NVRUrl=
* Be sure you have a correct value for the PIN. After 3 times restart of the interface and entering a wrong pin, the SIM is locked and you need to .=*
* enter the PUK by putting the SIM into a mobilephone. .=*
PIN=5028
Number=
* Enter the number of the SIM inserted. This is needet to send SMS to itself to check all the functionalities from sending till receiving. .=*
OwnNumber=
EnableSMSPDUMode=0
InternationalPrefix=00
NationalPrefix=0
MMSURLServer=
MMSAPN=
MMSIPAddress=
MMSPortType=
MMSLogin=
MMSPWD=
MMSContentType=application/vnd.wap.multipart.mixed
EnableMMS=1
* Retry functions: When sending not was successful it's possible, that there was just a short failure of the modem. So a retry would make sense .=*
RetryCount=5
RetryDelay=120
* RetryOnOtherModule: ( value 0 or 1): retry sending the message on another module if the 'RetryCount' attempts failed with the first module .=*
* It only works with many nvgsms module (and many GPRS modems) .=*
RetryOnOtherModule=0
* CapitalizeCommands is a function mostly not used. Just in case the modem requires it .=*
CapitalizeCommands=0
* TechAlarmNbr is the watchdog-alarm number when in section [ProblemHandling] no alarmnumber is defined .=*
TechAlarmNbr=9950
* Time to sleep after a technical alarm in minutes .=*
SleepMinAfterAlarm=60
* MaxMsgLength is the length where a message would be cut by the interface. Maximum of this value is 2000 .=*
MaxMsgLength=800
FloodProtection=0
IncomingEnable=1
* QualityPollEverySecs is the time between the checks, if the modem has enough signalstrength and can make a registration .=*
QualityPollEverySecs=5
* TestSMS is a function that sends periodical an SMS to itself (needs the OwnNumber). If not successful it starts an alarm .=*
TestSMSActive=0
SendTestSMSEveryMinutes=30
WaitForTestSMSAfterSendingInSecs=120
WaitAfterSendSecs=0
* Data Scheme coding parameter - not yet implemented .=*
DSC=0
DisplaySMSCInfo=1
AutoConnectSetOnSIM=0
VoiceCallDuration=30
* If the warning because of low signalstrength is occuring all the time,=*
* even the module works with the low signalstrength, then you can deactivate the warning .=*
DeactivateSignalStrengthWarningsInLog=0
* These parameters are for the test-function in the interfacemonitor. So you can handle every interface independant .=*
TestDescriptionForMonInterface=Welcome to the function to test the NVGSMS-interface! Please enter a number, you can check if the sending was successful. The message is static.
TestMessageForMonInterface=This is a Mobicall testmessage sent by the interface monitor.
* ActivateInputThreadHandler in case the SIM sometimes blocks .=*
ActivateInputThreadHandler=0
* ActivateExtendedLogs to have more info in log .=*
ActivateExtendedLogs=0
IsSecondarySupervisePrimary=0
PrimarySupervisionIntervalInSeconds=30
ProcessErrorOfPrimaryWhenSupervising=0
TestLastNbrForMonInterface=06504198296
[ProblemHandling]
* On an error you can set the status of an alarm to 1. On success back to 0. If this function is activated, you can define for input- and output- .=*
* alarms different alarms where this should be done .=*
* On error and/or on success you can start an alarm. It's actually the watchdogalarm. But these alarms don't start when the connection failed .=*
* (then the interface restarts). And then on a failed identification (after restart) -> the alarm starts .=*
AlarmDbPath=..\db1
LimitOfSmallErrorsBeforeRestart=10
LimitOfRestartsBeforeStartTechnicalAlarm=2
DoNotMoveJobOnSendingErrorBeforeRestart=0
OnErrorSetStatusOfAlarmTo1=
OnInputErrorSetStatusOfAlarm=
OnInputErrorStartAlarm=
OnOutputErrorSetStatusOfAlarm=
OnOutputErrorStartAlarm=
OnSuccessSetStatusOfAlarmTo0=
OnInputSuccessSetStatusOfAlarm=
OnInputSuccessStartAlarm=
OnOutputSuccessSetStatusOfAlarm=
OnOutputSuccessStartAlarm=
OnlyLaunchSuccessAfterError=
[Statistics]
LastStartup=52088649
FirstInstallation=51ef99d7
LastWDAlr=52087FD4
LastWDSuc=5241999F
[Error_Count]
InitOut_0=0
InitIn_0=0
Restart_Count=0
[SMSCentralInfo]
#For information the current SMS-Central#=*
#To change please use a mobile phone an change on SIM-Card#=*
#79999000 as example for swisscom gsm network. For all other networks, please check www.airport1.de/handymsc.htm or #=*
CurrentSMSCNumber=+43676021
CurrentSMSCNumPlan=145